2012年2月11日土曜日

Mooring Whips How To Rig

mooring whips how to rig

CHA Seeks Corps Permit to Install Fixed Landing, Dredge Material in Old Saybrook

The Channelside Homeowners Association is seeking a permit from the U.S. Army Corps of Engineers, New England District to conduct work in waters of the United States in conjunction with installing a fixed landing and dredging of material in Old Saybrook, Conn.


The applicant proposes to install an 8-foot by 12-foot fixed landing with two, 3.5-foot-wide by 24-foot long hinged ramps to either side with associated pilings; 520 linear feet of 8-foot wide floats with associated ramps on either side of the landing, directly landward of the bulkhead; and two, 8-foot by 10-foot fixed access ramps, one at each end of the 520-foot long section, in order to provide recreational boating access for the Channelside neighborhood.

The man-made basin is approximately 110 feet wide at the southwestern end and approximately 140 feet wide at the northeastern end. The structures will encroach approximately 13 feet channelward of the bulkhead.


Some 600 linear feet of new wooden bulkhead sheeting will be installed 18 inches channelward of the existing concrete revetment, with associated support piles and mooring whips for berthing. The area landward of the new bulkhead will be backfilled with approximately 150 cubic yards of clean fill material. The new bulkhead revetment will replace the existing failed concrete tub revetment that is currently eroding into the basin. No tidal wetlands will be impacted as a result of the bulkhead installation.

The proposed work is located in a man-made basin to the south of the Connecticut River at Channelside Drive in Old Saybrook.


Approximately 1,500 cubic yards of silt and mud will be dredged to a depth of –3 feet mean low water, with a clamshell bucket, over a 25,000-square-foot area beneath and adjacent to the proposed dock structures. There will be a 1-foot over-dredge allowance. The dredge material will be transported and disposed of at the Central Long Island Sound open water disposal site. The material has undergone a suitability determination for such open water disposal and the Corps has deemed the material suitable.

Dredging Today Staff, February 8, 2012; Image: usace



These are our most popular posts: mooring whips how to rig

Serious injury during supply boat mooring operation ...

The whip effect created, throw one crew member overboard. He was quickly rescued from the water but had suffered very serious injuries that easily could have been fatal. Causes: The first mooring rope from the rig was ... read more

No. learn more. - BECKER v. TIDEWATER INC LLC - US 5th Circuit

While the steel hose was extended, the REPUBLIC TIDEs movements caused the hose to whip across the rigs deck. To help keep the hose in place, Bakers employees ran it through a Baker-designed, ... The REPUBLIC TIDE, still connected by the starboard-stern mooring line and the (slack) steel hose, and still being pushed starboard, would collide with the oil rig without intervention. Captain Lachney instructed Baker crew members aboard the boat to disconnect ... read more

Dock Side Mooring Whips (Boats to 33 ) - Latest Hunting Information ...

Mooring Whips are a practical and effective solution to rough- water woes. Made of the highest quality fiberglass that is totally unaffected by temperature extremes, these whips serve as a spring to hold your rig away [...] ... read more

Yamaha Boaters Log Vol 3 No. 15 – Securing Your Boat to a Dock ...

Click on image for larger picture. Mooring whips are great for securing your boat in tidal, windy, or high-traffic areas. ... Or, lacking a centrally-located dock cleat, if your boat has a cleat (or cleats) on the gunwale close to its center, you can rig spring lines from the amidships cleat(s) aft to where the stern line is tied to the dock, and forward to the bow line dock cleat. (See illustration below). If you find yourself in a slip, instead of parallel-parked at a dock, you can rig two ... read more

Related Posts



0 コメント:

コメントを投稿